86636201 Default Parameter List for Rural

Sheet1 Category Parameter Name Value GSM Cell Cell Extension Type Normal cell GSM Cell BCCH IUO of Double Frequency Cell Extra GSM Cell Start Flex MAIO Switch Off GSM Cell CS Voice Service PRI 3 GSM Cell CS Data Service PRI 5 GSM Cell PS High PRI Service PRI 4 GSM Cell PS Low PRI Service PRI 6 GSM Cell Number of PBCCH Blocks 1 GSM Cell Number of PAGCH Blocks 4 GSM Cell Number of PRACH Blocks 1 GSM Cell Operator Name Grameenphone GSM Cell VIP Cell No GSM Cell MOCN Sharing Cell No GSM Cell Support Dual High Frequency Bands No GSM Cell active status Active Basic Attributes Layer of The Cell 3 Basic Attributes Cell Priority Priority-1 Basic Attributes Max TA 63 Basic Attributes FR Use Downlink DTX Yes Basic Attributes HR Use Downlink DTX Yes Basic Attributes Encryption Algorithm 11100000 Basic Attributes Minimum Access RXLEV 0 Basic Attributes FR Uplink DTX Shall Use Basic Attributes HR Uplink DTX Shall Use Basic Attributes Call Reestablishment Forbidden Yes Basic Attributes TCH Immediate Assignment No Basic Attributes Directed Retry Yes Basic Attributes UL PC Allowed Yes Basic Attributes DL PC Allowed Yes Basic Attributes SDCCH Dynamic Allocation Allowed Yes Basic Attributes Level Report Switch Support Basic Attributes Allow Dynamic Shutdown of TRX Yes Basic Attributes Adjust Voltage Yes Basic Attributes Diversity Transmitter GMSK Delay 20 Basic Attributes Diversity Transmitter 8PSK Delay 4 Basic Attributes ICB Allowed NO Basic Attributes Voltage Adjust Based Timeslots Allowed No Basic Attributes Diversity Transmitter 16QAM Delay 4 Basic Attributes Diversity Transmitter 32QAM Delay 4 Basic Attributes 16QAM Transmitter Power Reduce Level 0 Basic Attributes 32QAM Transmitter Power Reduce Level 0 Basic Attributes Cell Scenario COMMON Basic Attributes Cell 8PSK Power Attenuation Grade 0 Basic Attributes Fast Call Setup TCH Usage Threshold 0 Basic Attributes Immediate Assignment Optimized NO Basic Attributes TFO Switch Enable Basic Attributes Measure Link Delay Switch Disable Basic Attributes High-Order Modulation Power Increase Allowed Not Allowed Basic Attributes GPRS GPRS Support as built-in PCU Basic Attributes GPRS EDGE Yes Basic Attributes GPRS EGPRS2-A No Basic Attributes GPRS Support NACC Yes Basic Attributes GPRS PACKET SI No Basic Attributes GPRS Support NC2 No Basic Attributes GPRS Routing Area 0 Basic Attributes GPRS Support DTM Not Support Basic Attributes GPRS Support Downlink Dual-Carrier Not Support Basic Attributes GPRS Support Reduced Latency Capability Not Support Basic Attributes GPRS Support Out Inter-RAT Inter-Cell PS Handover Not Support Basic Attributes GPRS Support In Inter-RAT Inter-cell PS Handover Not Support Basic Attributes GPRS Support In LTE Inter-cell PS Handover Not Support Basic Attributes GPRS Support Out LTE Inter-cell PS Handover Not Support Basic Attributes GPRS Support DPI Not Support Idle Mode Basic Parameters Attach-detach Allowed Yes Idle Mode Basic Parameters TX-integer 50 Idle Mode Basic Parameters Cell Bar Access NO Idle Mode Basic Parameters Cell Bar Qualify No Idle Mode Basic Parameters CCCH Blocks Reserved for AGCH 1 Idle Mode Basic Parameters Multi-Frames in a Cycle on the Paging CH 2 Multiframe Period Idle Mode Basic Parameters T3212 50 Idle Mode Basic Parameters Cell Reselect Hysteresis Parameters 6dB Idle Mode Basic Parameters Cell Reselect Parameters Indication Yes Idle Mode Basic Parameters NCC Permitted 11111111 Idle Mode Basic Parameters Cell Reselect Offset 0 Idle Mode Advance Parameter Additional Reselect Parameter Indication Flexible Idle Mode Advance Parameter Cell Reselect Temporary Offset 0 Idle Mode Advance Parameter Cell Reselect Penalty Time 0 Call Control Basic Parameters SACCH Multi-Frames 20 Call Control Basic Parameters RACH Busy Threshold 16 Call Control Basic Parameters Paging Times 4 Call Control Basic Parameters Assignment Cell Load Judge Enable Disable Call Control Basic Parameters Directed Retry Load Access Threshold 70 Call Control Basic Parameters AFR SACCH Multi-Frames 36 Call Control Basic Parameters AHR SACCH Multi-Frames 28 Call Control Basic Parameters AFR Radio Link Timeout 36_Times Call Control Basic Parameters AHR Radio Link Timeout 28_Times Call Control Basic Parameters MS MAX Retrans 4_Times Call Control Basic Parameters Common Access Control Class 0 Call Control Basic Parameters Special Access Control Class 0 Call Control Basic Parameters Emergency Call Disable No Call Control Basic Parameters Radio Link Timeout 20_Times Call Control Basic Parameters ECSC Yes Call Control Basic Parameters Multi-band report 0 Call Control Basic Parameters Allow Reassign Yes Call Control Basic Parameters Allow EMLPP No Call Control Basic Parameters Repeated Downlink FACCH No Call Control Basic Parameters Repeated SACCH No Call Control Basic Parameters Access Control Allowed No Access Control Parameters Speech Version 1011010 Access Control Parameters TRX Aiding Function Control Allowed AND Recover When Chk Res Access Control Parameters Random Access Error Threshold 180 Access Control Parameters Power Deviation Indication Yes Access Control Parameters Power Deviation 1 Access Control Parameters CS RACH Min Access Level -110 Access Control Parameters PS RACH Min Access Level -110 Access Control Parameters Switchback Policy of Baseband FH Mutual Aid All Call Control Timer Parameters T200 SDCCH 60 Call Control Timer Parameters T200 FACCH/F 50 Call Control Timer Parameters T200 FACCH/H 50 Call Control Timer Parameters T200 SACCH TCH SAPI0 150 Call Control Timer Parameters T200 SACCH TCH SAPI3 200 Call Control Timer Parameters T200 SACCH SDCCH 60 Call Control Timer Parameters T200 SDCCH SAPI3 60 Call Control Timer Parameters Use LAPDm N200 Off Call Control Timer Parameters Use IMM ASS Retransmit Parameter No Call Control Advance Parameters Short Message Uplink Disabled No Call Control Advance Parameters Short Message Downlink Disabled No Call Control Advance Parameters Frequency Band of Reassign Different Band Call Control Advance Parameters Emergency Call Preemption Permitted Off Call Control Advance Parameters Priority of Emergency Call 15 Call Control Advance Parameters Select 3G Cell After Call Release No Call Control Advance Parameters Max TA Drop Call Switch Off Call Control Advance Parameters MAX TA Drop Call Filter 20 Call Control Advance Parameters MAX TA Drop Call Threshold 63 Call Control Advance Parameters Select 3G Cell If No TD Cell Is Contained In MR OFF Call Control Advance Parameters Channel of Sending SI13 Message BCCH Norm Amr Parameters AMR Rate Control Switch Algorithm I Amr Parameters AMR ACS[F] 10101001 Amr Parameters AMR UL Coding Rate adjth1[F] 12 Amr Parameters AMR UL Coding Rate adjth2[F] 16 Amr Parameters AMR UL Coding Rate adjth3[F] 25 Amr Parameters AMR UL Coding Rate adjhyst1[F] 2 Amr Parameters AMR UL Coding Rate adjhyst2[F] 2 Amr Parameters AMR UL Coding Rate adjhyst3[F] 3 Amr Parameters AMR DL Coding Rate adjth1[F] 12 Amr Parameters AMR DL Coding Rate adjth2[F] 16 Amr Parameters AMR DL Coding Rate adjth3[F] 25 Amr Parameters AMR DL Coding Rate adjhyst1[F] 2 Amr Parameters AMR DL Coding Rate adjhyst2[F] 2 Amr Parameters AMR DL Coding Rate adjhyst3[F] 3 Amr Parameters AMR Starting Mode[F] 1 Amr Parameters AMR ACS[H] 101010 Amr Parameters AMR UL Coding Rate adjth1[H] 23 Amr Parameters AMR UL Coding Rate adjth2[H] 31 Amr Parameters AMR UL Coding Rate adjth3[H] 63 Amr Parameters AMR UL Coding Rate adjhyst1[H] 3 Amr Parameters AMR UL Coding Rate adjhyst2[H] 4 Amr Parameters AMR UL Coding Rate adjhyst3[H] 15 Amr Parameters AMR DL Coding Rate adjth1[H] 23 Amr Parameters AMR DL Coding Rate adjth2[H] 31 Amr Parameters AMR DL Coding Rate adjth3[H] 63 Amr Parameters AMR DL Coding Rate adjhyst1[H] 3 Amr Parameters AMR DL Coding Rate adjhyst2[H] 4 Amr Parameters AMR DL Coding Rate adjhyst3[H] 15 Amr Parameters AMR Starting Mode[H] 0 Amr Parameters AMR Uplink Adaptive Threshold Allowed No Amr Parameters Uplink Long-term FER Upper Threshold 60 Amr Parameters Uplink Long-term FER Lower Threshold 2 Amr Parameters Uplink Long-term FER Target 8 Amr Parameters Uplink Threshold Adjust Factor 40 Amr Parameters AMR Downlink Adaptive Threshold Allowed No Amr Parameters Downlink Long-term FER Upper Threshold 60 Amr Parameters Downlink Long-term FER Lower Threshold 2 Amr Parameters Downlink Long-term FER Target 8 Amr Parameters Downlink Threshold Adjust Factor 2 Amr Parameters AMR ACS[WB] 111 Amr Parameters AMR UL Coding Rate adjth1[WB] 21 Amr Parameters AMR UL Coding Rate adjth2[WB] 25 Amr Parameters AMR UL Coding Rate adjhyst1[WB] 2 Amr Parameters AMR UL Coding Rate adjhyst2[WB] 2 Amr Parameters AMR DL Coding Rate adjth1[WB] 12 Amr Parameters AMR DL Coding Rate adjth2[WB] 18 Amr Parameters AMR DL Coding Rate adjhyst1[WB] 2 Amr Parameters AMR DL Coding Rate adjhyst2[WB] 2 Amr Parameters AMR Starting Mode[WB] 2 Amr Parameters Is RATSCCH Function Enabled Disable Handover Basic Parameters Current HO Control Algorithm Handover algorithm I Handover Basic Parameters Co-BSC/MSC Adj No Handover Basic Parameters SDCCH HO Allowed No Handover Basic Parameters Intracell HO Allowed No Handover Basic Parameters Intracell F-H HO Allowed Yes Handover Basic Parameters Load Handover Support No Handover Basic Parameters MS Fast Moving HO Allowed No Handover Basic Parameters Rx_Level_Drop HO Allowed No Handover Basic Parameters PBGT HO Allowed Yes Handover Basic Parameters Level HO Allowed Yes Handover Basic Parameters Edge HO Allowed Yes Handover Basic Parameters BQ HO Allowed Yes Handover Basic Parameters TA HO Allowed Yes Handover Basic Parameters Concentric Circles HO Allowed Yes Handover Basic Parameters Interference HO Allowed Yes Handover Basic Parameters Edge HO UL RX_LEV Threshold 10 Handover Basic Parameters Edge HO DL RX_LEV Threshold 20 Handover Basic Parameters Intracell F-H HO Stat Time 6 Handover Basic Parameters Intracell F-H HO Last Time 4 Handover Basic Parameters F2H HO Threshold 21 Handover Basic Parameters H2F HO Threshold 13 Handover Basic Parameters Inter-layer HO Threshold 5 Handover Basic Parameters Inter-layer HO Hysteresis 2 Handover Basic Parameters Min UL Level on Candidate Cell 0 Handover Basic Parameters Min DL Level on Candidate Cell 8 Handover Basic Parameters TIGHT BCCH HO Watch Time 6 Handover Basic Parameters TIGHT BCCH HO Valid Time 4 Handover Basic Parameters Quick Handover Enable No Handover Basic Parameters Concentric Circles ATCB HO Allowed Close Handover Basic Parameters Inter-RAT Out BSC Handover Enable No Handover Basic Parameters Inter-RAT In BSC Handover Enable No Handover Basic Parameters Allow Incoming BSC Handover at Iur-g No Handover Basic Parameters Carry Speech Data at Iur-g No Handover Basic Parameters Inter-RAT Cell Reselection Enable No Handover Basic Parameters Handover Algorithm I Edge HO Watch Time 6 Handover Basic Parameters Handover Algorithm I Edge HO Valid Time 4 Handover Basic Parameters LTE Cell Reselection Allowed No Handover Basic Parameters SRVCC Handover Allowed No Handover Basic Parameters LTE SAI MCC 0 Handover Basic Parameters LTE SAI MNC 0 Handover Basic Parameters LTE SAI LAC 1 Handover Basic Parameters LTE SAI SAC 0 Handover Control Parameters Min Interval for TCH Hos 2 Handover Control Parameters Min Interval for SDCCH Hos 2 Handover Control Parameters Min Interval for Consecutive HOs 5 Handover Control Parameters Min Interval for Emerg HO 5 Handover Control Parameters Inter-BSC SDCCH HO ALLowed No Handover Control Parameters Penalty Allowed Yes Handover Control Parameters MRPreprocessing BSC preprocessing Handover Control Parameters Min Power Level For Directed Retry 16 Handover Advance Data System Flux Threshold for Load HO 10 Handover Advance Data Load HO Threshold 90 Handover Advance Data Load handover Load Accept Threshold 80 Handover Advance Data Load HO Bandwidth 25 Handover Advance Data Load HO Step Period 10 Handover Advance Data Load HO Step Level 5 Handover Advance Data MS Fast-moving Watch Cells 3 Handover Advance Data MS Fast-moving Valid Cells 2 Handover Advance Data MS Fast-moving Time Threshold 15 Handover Advance Data MAX Consecutive HO Times 2 Handover Advance Data Forbidden time after MAX Times 15 Handover Advance Data Interval for Consecutive HO Jud 7 Handover Advance Data Penalty on MS Fast Moving HO 30 Handover Advance Data Penalty Time on Fast Moving HO 0 Handover Advance Data K Bias 0 Handover Advance Data RX_QUAL Threshold for TIGHT BCCH HO 3 Handover Advance Data Load Threshold for TIGHT BCCH HO 80 Handover Advance Data Max Resend Times of PhyInfo 30 Handover Advance Data T3105 8 Handover Advance Data Inter BSC Load Information Allowed No Handover Advance Data Waiting for MR on SDCCH Switch Off Handover Advance Data Duration for Waiting MR on SDCCH 10 Handover Advance Data Assigning Better Cell Allowed Off Handover Advance Data Maximum Better Cell Assigning Duration 40 Handover Advance Data Uplink Quality Threshold in Assigning Better Cell 50 Handover Advance Data Downlink Quality Threshold in Assigning Better Cell 50 Handover Advance Data Enhanced Load HO Allowed NO Handover Advance Data Inter-Layer HO Load Threshold 0 Handover Advance Data HO Ratio of Enhanced Load HO Algorithm 3 Iuo Handover Parameter UL to OL HO Allowed Yes Iuo Handover Parameter OL to UL HO Allowed Yes Iuo Handover Parameter RX_LEV for UO HO Allowed Yes Iuo Handover Parameter RX_QUAL for UO HO Allowed No Iuo Handover Parameter TA for UO HO Allowed No Iuo Handover Parameter RX_LEV Threshold 30 Iuo Handover Parameter RX_LEV Hysteresis 5 Iuo Handover Parameter RX_QUAL Threshold 60 Iuo Handover Parameter TA Threshold 61 Iuo Handover Parameter TA Hysteresis 0 Iuo Handover Parameter UO HO Watch Time 10 Iuo Handover Parameter UO HO Valid Time 8 Iuo Handover Parameter Assign Optimum Layer System optimization Iuo Handover Parameter Assign-optimum-level Threshold 24 Iuo Handover Parameter TA Threshold of Assignment Pref 61 Iuo Handover Parameter TA Pref of Imme-Assign Allowed No Iuo Handover Parameter TA Threshold of Imme-Assign Pref 61 Iuo Handover Parameter Pref Subcell in HO of Intra-BSC System optimization Iuo Handover Parameter Incoming-to-BSC HO Optimum Layer Underlaid subcell Iuo Handover Parameter OtoU HO Received Level Threshold 16 Iuo Handover Parameter UtoO HO Received Level Threshold 25 Iuo Handover Parameter UtoO Traffic HO Allowed No Iuo Handover Parameter Underlay HO Step Period 5 Iuo Handover Parameter Penalty Time of UtoO HO 10 Iuo Handover Parameter Penalty Time after UtoO HO Fail 40 Iuo Handover Parameter Penalty Time after OtoU HO Fail 10 Iuo Handover Parameter MaxRetry Time after UtoO Fail 3 Iuo Handover Parameter En Iuo Out Cell Low Load Thred 20 Iuo Handover Parameter En Iuo Out Cell General OverLoad Thred 70 Iuo Handover Parameter En Iuo Out Cell Serious OverLoad Thred 80 Iuo Handover Parameter Load Classification HO Period 5 Iuo Handover Parameter Load Classification HO Step 5 Iuo Handover Parameter ReceiveQualThrshAMRFR 50 Iuo Handover Parameter ReceiveQualThrshAMRHR 40 Iuo Handover Parameter Underlay HO Step Level 5 Iuo Handover Parameter PS OtoU HO Receive Level Threshold 25 Iuo Handover Parameter PS UtoO HO Receive Level Threshold 35 Data Filter/Penalty Parameter Current HO Control Algorithm Handover algorithm I Data Filter/Penalty Parameter Allowed MR Number Lost 3 Data Filter/Penalty Parameter Filter Length for TCH Level 4 Data Filter/Penalty Parameter Filter Length for TCH Qual 6 Data Filter/Penalty Parameter Filter Length for SDCCH Level 2 Data Filter/Penalty Parameter Filter Length for SDCCH Qual 2 Data Filter/Penalty Parameter Filter Length for Ncell RX_LEV 4 Data Filter/Penalty Parameter Filter Length for TA 4 Data Filter/Penalty Parameter Penalty Level after HO Fail 63 Data Filter/Penalty Parameter Penalty Level after BQ HO 7 Data Filter/Penalty Parameter Penalty Time after BQ HO 15 Data Filter/Penalty Parameter Penalty Level after TA HO 63 Data Filter/Penalty Parameter Penalty Time after TA HO 10 Data Filter/Penalty Parameter Penalty Time after AMR TCHF-H HO Fail 10 Data Filter/Penalty Parameter RscPenaltyTimer 4 Data Filter/Penalty Parameter UmPenaltyTimer 10 Data Filter/Penalty Parameter CfgPenaltyTimer 255 Data Filter/Penalty Parameter Filter Length for SDCCH MEAN_BEP 2 Data Filter/Penalty Parameter Filter Length for TCH MEAN_BEP 6 Data Filter/Penalty Parameter Filter Length for SDCCH CV_BEP 2 Data Filter/Penalty Parameter Filter Length for TCH CV_BEP 6 Data Filter/Penalty Parameter Filter Length for SDCCH REP_QUANT 2 Data Filter/Penalty Parameter Filter Length for TCH REP_QUANT 6 Data Filter/Penalty Parameter Filter Length for SDCCH NBR_RCVD_BLOCK 2 Data Filter/Penalty Parameter Filter Length for TCH NBR_RCVD_BLOCK 6 Emergency Handover Data Current HO Control Algorithm Handover algorithm I Emergency Handover Data TA Threshold 61 Emergency Handover Data DL Qual Threshold 60 Emergency Handover Data UL Qual Threshold 60 Emergency Handover Data Filter Parameter A1 10 Emergency Handover Data Filter Parameter A2 10 Emergency Handover Data Filter Parameter A3 10 Emergency Handover Data Filter Parameter A4 10 Emergency Handover Data Filter Parameter A5 10 Emergency Handover Data Filter Parameter A6 10 Emergency Handover Data Filter Parameter A7 10 Emergency Handover Data Filter Parameter A8 10 Emergency Handover Data Filter Parameter B 0 Emergency Handover Data No Dl MrHO Allowed No Emergency Handover Data No Dl MrUl Qual HO Limit 50 Emergency Handover Data ConsNo Dl MrHO Allowed Limit 8 Amr Qual Parameter Interfere HO Qual Thresh 1 for Non-AMR FR 70 Amr Qual Parameter Interfere HO Qual Thresh 2 for Non-AMR FR 60 Amr Qual Parameter Interfere HO Qual Thresh 3 for Non-AMR FR 59 Amr Qual Parameter Interfere HO Qual Thresh 4 for Non-AMR FR 58 Amr Qual Parameter Interfere HO Qual Thresh 5 for Non-AMR FR 57 Amr Qual Parameter Interfere HO Qual Thresh 6 for Non-AMR FR 56 Amr Qual Parameter Interfere HO Qual Thresh 7 for Non-AMR FR 55 Amr Qual Parameter Interfere HO Qual Thresh 8 for Non-AMR FR 54 Amr Qual Parameter Interfere HO Qual Thresh 9 for Non-AMR FR 53 Amr Qual Parameter Interfere HO Qual Thresh 10 for Non-AMR FR 52 Amr Qual Parameter Interfere HO Qual Thresh 11 for Non-AMR FR 51 Amr Qual Parameter Interfere HO Qual Thresh 12 for Non-AMR FR 50 Amr Qual Parameter Interfere HO Qual Thresh Offset for AMR FR 5 Amr Qual Parameter DL Qual Limit for AMR FR 65 Amr Qual Parameter UL Qual Limit for AMR FR 65 Amr Qual Parameter DL Qual Limit for AMR HR 60 Amr Qual Parameter UL Qual Limit for AMR HR 60 Fast Handover Parameter Quick Handover Up Trigger Level 50 Fast Handover Parameter Quick Handover Down Trigger Level 50 Fast Handover Parameter Quick Move Speed Threshold 35 Fast Handover Parameter Serving Cell Filter Length MR Number 4 Fast Handover Parameter Neighbor Cell Filter Length MR Number 4 Fast Handover Parameter Ignore Measurement Report Number 1 Fast Handover Parameter Quick Handover Punish Time 10 Fast Handover Parameter Quick Handover Punish Value 63 Fast Handover Parameter Quick Handover Offset 68 Fast Handover Parameter EN Quick PBGT HO ALG When MS Leaves BTS No Fast Handover Parameter Handover Direction Forecast Enable No Fast Handover Parameter Handover Direction Forecast Statistic Times 3 Fast Handover Parameter Handover Direction Forecast Last Times 3 Fast Handover Parameter Frequency Shift Handover Statistic Time 4 Fast Handover Parameter Frequency Shift Handover Duration 3 Enhance Dual Band Parameter UL Subcell Lower Load Threshold 50 Enhance Dual Band Parameter UL Subcell Assignment Optimization Yes Enhance Dual Band Parameter OL Subcell Assignment Optimization No Enhance Dual Band Parameter UL Subcell General Overload Threshold 80 Enhance Dual Band Parameter UL Subcell Serious Overload Threshold 90 Enhance Dual Band Parameter Subcell HO Allowed Flow Control Level 10 Enhance Dual Band Parameter Distance Between Boundaries of Subcells 10 Enhance Dual Band Parameter Distance Hysteresis Between Boundaries 2 Enhance Dual Band Parameter Load HO Allowed No Enhance Dual Band Parameter UL Subcell Load Hierarchical HO Periods 5 Enhance Dual Band Parameter Step Length of UL Subcell Load HO 5 Enhance Dual Band Parameter MOD Step LEN of UL Load HO Period 1 Enhance Dual Band Parameter Load HO of OL Subcell to UL Subcell No Enhance Dual Band Parameter OL Subcell Load Diversity HO Period 10 Enhance Dual Band Parameter Step Length of OL Subcell Load HO 5 Enhance Dual Band Parameter Incoming OL Subcell HO Level TH 30 Enhance Dual Band Parameter Outgoing OL Subcell HO Level TH 25 Enhance Dual Band Parameter Inter UL/OL Subcells HO Penalty Time 5 Enhance Dual Band Parameter Total Number of Measurements 5 Enhance Dual Band Parameter Number of Satisfactory Measurements 4 Enhance Dual Band Parameter Inner Cell EDGE HO Enable Yes Enhance Dual Band Parameter Inner Cell Serious OverLoad Thred 90 Power Control Basic Parameters PC Interval 3 Power Control Basic Parameters UL RX_LEV Upper Threshold 32 Power Control Basic Parameters UL RX_LEV Lower Threshold 32 Power Control Basic Parameters UL Qual Upper Threshold 0 Power Control Basic Parameters UL Qual Lower Threshold 3 Power Control Basic Parameters DL RX_LEV Upper Threshold 48 Power Control Basic Parameters DL RX_LEV Lower Threshold 25 Power Control Basic Parameters DL Qual Upper Threshold 0 Power Control Basic Parameters DL Qual Lower Threshold 2 Power Control Basic Parameters Power Control Switch Power controlIII Power Control Basic Parameters AMR SACCH Downlink Power Upgrade 0 Power Control Basic Parameters Power Forecast Allowed No Power Control Basic Parameters Combiner Loss 45 Power Control Basic Parameters Double Antenna Gain 30 Power Control Basic Parameters Path Loss of Different Frequency Band 79 Power Control Basic Parameters Expected DL RX_LEV 30 Power Control Basic Parameters Expected UL RX_LEV 30 Power Control Basic Parameters SAIC Allowed No II Power Control Parameters Filter Length for UL RX_LEV 5 II Power Control Parameters Filter Length for DL RX_LEV 5 II Power Control Parameters Filter Length for UL Qual 5 II Power Control Parameters Filter Length for DL Qual 5 II Power Control Parameters MR Compensation Allowed Yes II Power Control Parameters UL MR Number Predicted 0 II Power Control Parameters DL MR Number Predicted 0 II Power Control Parameters MAX Down AdjValue QualZone 0 2 II Power Control Parameters MAX Down AdjValue QualZone 1 0 II Power Control Parameters MAX Down AdjValue QualZone 2 0 II Power Control Parameters MAX Down Adj PC Value by Qual 2 II Power Control Parameters MAX Up Adj PC Value by RX_LEV 8 II Power Control Parameters MAX Up Adj PC Value by Qual 8 II Power Control Parameters UL Qual Bad Trig Threshold 3 II Power Control Parameters UL Qual Bad UpLEVDiff 5 II Power Control Parameters DL Qual Bad Trig Threshold 2 II Power Control Parameters DL Qual Bad UpLEVDiff 10 II Power Control Parameters BTS PC Class 16 II Power Control Parameters AMR PC Interval 3 II Power Control Parameters AMR Filter Length for UL RX_LEV 5 II Power Control Parameters AMR Filter Length for DL RX_LEV 5 II Power Control Parameters AMR Filter Length for UL Qual 5 II Power Control Parameters AMR Filter Length for DL Qual 5 II Power Control Parameters AMR MR Compensation Allowed Yes II Power Control Parameters AMR UL MR Number Predicted 0 II Power Control Parameters AMR DL MR Number Predicted 0 II Power Control Parameters AMR UL RX_LEV Upper Threshold 25 II Power Control Parameters AMR UL RX_LEV Lower Threshold 18 II Power Control Parameters AMR UL Qual Upper Threshold 0 II Power Control Parameters AMR UL Qual Lower Threshold 3 II Power Control Parameters AMR DL RX_LEV Upper Threshold 33 II Power Control Parameters AMR DL RX_LEV Lower Threshold 25 II Power Control Parameters AMR DL Qual Upper Threshold 0 II Power Control Parameters AMR DL Qual Lower Threshold 3 II Power Control Parameters AMR MAX Down Adj Value Qual Zone 0 2 II Power Control Parameters AMR MAX Down Adj Value Qual Zone 1 0 II Power Control Parameters AMR MAX Down Adj Value Qual Zone 2 0 II Power Control Parameters AMR MAX Down Adj PC Value by Qual 4 II Power Control Parameters AMR MAX Up Adj PC Value by RX_LEV 8 II Power Control Parameters AMR MAX Up Adj PC Value by Qual 8 II Power Control Parameters AMR UL Qual Bad Trig Threshold 3 II Power Control Parameters AMR UL Qual Bad UpLEVDiff 6 II Power Control Parameters AMR DL Qual Bad Trig Threshold 2 II Power Control Parameters AMR DL Qual Bad UpLEVDiff 8 II Power Control Parameters AMR BTS PC Class 16 II Power Control Parameters Power Control Threshold Adjust for SAIC 1 III Power Control Parameters MRMissNumber 3 III Power Control Parameters PwrCtrlULAdjPeriod 3 III Power Control Parameters PwrCtrlDLAdjPeriod 2 III Power Control Parameters SdMrCutNum 1 III Power Control Parameters TchMrCutNum 2 III Power Control Parameters DLRexLevExponentFilterLen 3 III Power Control Parameters DLRexQualExponentFilterLen 3 III Power Control Parameters DLRexLevSlideWindow 1 III Power Control Parameters DLRexQualSlideWindow 1 III Power Control Parameters DLRexLevAdjustFactor 3 III Power Control Parameters DLRexQualAdjustFactor 4 III Power Control Parameters DLRexLevHighThred 22 III Power Control Parameters DLRexLevLowthred 22 III Power Control Parameters DLFSRexQualHighThred 14 III Power Control Parameters DLFSRexQualLowThred 14 III Power Control Parameters DLHSRexQualHighThred 14 III Power Control Parameters DLHSRexQualLowThred 14 III Power Control Parameters DLAFSRexQualHighThred 14 III Power Control Parameters DLAFSRexQualLowThred 14 III Power Control Parameters DLAHSRexQualHighThred 14 III Power Control Parameters DLAHSRexQualLowThred 14 III Power Control Parameters DLMAXDownStep 12 III Power Control Parameters DLMAXUpStep 20 III Power Control Parameters ULRexLevExponentFilterLen 3 III Power Control Parameters ULRexQualExponentFilterLen 3 III Power Control Parameters ULRexLevSlideWindow 1 III Power Control Parameters ULRexQualSlideWindow 1 III Power Control Parameters ULRexLevAdjustFactor 3 III Power Control Parameters ULRexQualAdjustFactor 4 III Power Control Parameters ULRexLevHighThred 20 III Power Control Parameters ULRexLevLowThred 20 III Power Control Parameters ULFSRexQualHighThred 14 III Power Control Parameters ULFSRexQualLowThred 14 III Power Control Parameters ULHSRexQualHighThred 14 III Power Control Parameters ULHSRexQualLowThred 14 III Power Control Parameters ULAFSRexQualHighThred 14 III Power Control Parameters ULAFSRexQualLowThred 14 III Power Control Parameters ULAHSRexQualHighThred 14 III Power Control Parameters ULAHSRexQualLowThred 14 III Power Control Parameters ULMAXDownStep 12 III Power Control Parameters ULMAXUpStep 20 III Power Control Parameters Power Control threshold Adjust for SAIC 0 III Power Control Parameters 02dB Power Control Enable No III Power Control Parameters III Power Control Optimized Enable Yes III Power Control Parameters III UL Filter Adjust Factor 3 III Power Control Parameters III DL Filter Adjust Factor 3 III Power Control Parameters III UL RexLev Protect Factor 6 III Power Control Parameters III UL RexQual Protect Factor 73 III Power Control Parameters III DL RexLev Protect Factor 5 III Power Control Parameters III DL RexQual Protect Factor 60 III Power Control Parameters Allow III Power Control For AMR Allowed III Power Control Parameters Allow III Power Control For Non-AMR Allowed Channel Management Basic Parameters Idle SDCCH Threshold N1 2 Channel Management Basic Parameters Cell SDCCH Channel Maximum 50 Channel Management Basic Parameters TCH Minimum Recovery Time 60 Channel Management Basic Parameters Grade Access Allow No Channel Management Basic Parameters Enhanced TCH Adjust Allowed Yes Channel Management Basic Parameters TIGHT BCCH Switch Off Channel Management Basic Parameters Dynamic Transmission Div Supported Not Support Channel Management Basic Parameters Channel Allocate Strategy Quality preferred Channel Management Basic Parameters Highest Priority User Quality First No Channel Management Basic Parameters Ratio of TCHH 100 Channel Management Basic Parameters Ratio of AMR-HR 100 Channel Management Basic Parameters Max Channel Num Reserved for EC 0 Channel Management Basic Parameters Different Band SDCCH Using Optimize No Channel Management Basic Parameters Factory Mode Off Dynamic Turning off Parameter Enable Turning Off Cell Disable Channel Management Advance Parameters TCH Traffic Busy Threshold 60 Channel Management Advance Parameters Interf Priority Allowed Yes Channel Management Advance Parameters Active CH Interf MeasAllowed Yes Channel Management Advance Parameters Allocation TRX Priority Allowed Yes Channel Management Advance Parameters History Record Priority Allowed Yes Channel Management Advance Parameters Balance Traffic Allowed Yes Channel Management Advance Parameters Interfof UL Level Threshold 35 Channel Management Advance Parameters Interfof UL Qual Threshold 30 Channel Management Advance Parameters Interfof DL Level Threshold 45 Channel Management Advance Parameters Interfof DL QualThreshold 30 Channel Management Advance Parameters Filter Length for TCH Level 6 Channel Management Advance Parameters Filter Length for TCH Qual 6 Channel Management Advance Parameters Filter Length for SDCCH Level 2 Channel Management Advance Parameters Filter Length for SDCCH Qual 2 Channel Management Advance Parameters AMR TCH/H Prior Allowed On Channel Management Advance Parameters AMR TCH/H Prior Cell Load Threshold 20 Channel Management Advance Parameters Tch Traffic Busy Overlay Threshold 60 Channel Management Advance Parameters Tch Traffic Busy Underlay Threshold 60 Channel Management Advance Parameters Load of UL-OL Cells Rate Select Allowed Yes Channel Management Advance Parameters Smooth Factor of Uplink Received Level 6 Channel Management Advance Parameters Duration of Uplink Received Level Differ 4 Channel Management Advance Parameters Observe Time of UL RX Level Difference 5 Channel Management Advance Parameters Multi-Density TRX Power Sharing None Channel Management Advance Parameters MCPA Optimization Switch Off Channel Management Advance Parameters Qtru Down Power Inadequate Stat Time 5 Channel Management Advance Parameters Qtru Down Power Inadequate Last Time 3 Channel Management Advance Parameters Power Priority Allowed Yes Channel Management Advance Parameters Level Thresh for Assign BCCH Under TBCCH 30 Channel Management Advance Parameters Quality Thresh for Assign BCCH Under TBCCH 1 Channel Management Advance Parameters Channel Assign Allow for Insuff Power No Channel Management Advance Parameters GSM900 Band Traffic Load Share Threshold 25 Channel Management Advance Parameters Assign Non-AMR User Loose Fre Reuse TRX No Channel Management Advance Parameters IBCA Allowed No Channel Management Advance Parameters IBCA User Dyn Measure Neighbor Cell No Channel Management Advance Parameters IUO IBCA Allowed Enabled in UL subcell Channel Management Advance Parameters IBCA Soft Block Switch No Channel Management Advance Parameters IBCA FR/EFR Soft Block Threshold 10 Channel Management Advance Parameters IBCA HR Soft Block Threshold 13 Channel Management Advance Parameters IBCA AMR FR Soft Block Threshold 4 Channel Management Advance Parameters IBCA AMR HR Soft Block Threshold 10 Channel Management Advance Parameters IBCA WAMR FR Soft Block Threshold 5 Channel Management Advance Parameters IBCA Soft Block SAIC Offset 1 Channel Management Advance Parameters IBCA Max Interference Source Num 20 Channel Management Advance Parameters IBCA Downlink Path Loss Offset 7 Channel Management Advance Parameters IBCA IUO Path Loss Offset 4 Channel Management Advance Parameters IBCA Service Cell Pathloss 110 Channel Management Advance Parameters IBCA Pathloss Offset 15 Channel Management Advance Parameters IBCA Call Information Filter 4 Channel Management Advance Parameters IBCA Loose Trx SDCCH Load Threshold 80 Channel Management Advance Parameters IBCA Tight Trx SDCCH Rxlev Threshold 40 Channel Management Advance Parameters IBCA Wait SDCCH Idle Timer 4 Channel Management Advance Parameters IBCA ICDM Switch Yes Channel Management Advance Parameters IBCA Path Lose Filter Factor 6 Channel Management Advance Parameters IBCA Pathloss Est of Non MR Ncell 0 Channel Management Advance Parameters IBCA Non Measurement Ncell Stat Num 4 Channel Management Advance Parameters IBCA MAIO Using Method Max optimized MAIO Channel Management Advance Parameters IBCA MAIO Target C/I Threshold 20 Channel Management Advance Parameters IBCA Init Power Control RexLevDL Offset 0 Channel Management Advance Parameters IBCA Init Power Control RexLevUL Offset 0 Channel Management Advance Parameters IBCA Init Pwr Ctrl Rx Qual DL Offset 0 Channel Management Advance Parameters IBCA Init Pwr Ctrl Rx Qual UL Offset 0 Channel Management Advance Parameters Allocate OL Channel Based on RX Level On Channel Management Advance Parameters Assign to Overlayer RxLev Offset 35 Channel Management Advance Parameters Handover to Overlayer RxLev Offset 29 Channel Management Advance Parameters IBCA Sub-Channel Handover Allowed Not Allowed Channel Management Advance Parameters IBCA Forced BTS Synchronization Allowed Not Allowed Channel Management Advance Parameters IBCA Flexible TSC Allowed Not Allowed Channel Management Advance Parameters IBCA Assign Waiting Mr Time 4 Channel Management Advance Parameters IBCA Natural HO Waiting Mr Time 5 Channel Management Advance Parameters IBCA Urgent HO Waiting Mr Time 0 Channel Management Advance Parameters IBCA HO Waiting Effective Mr Time 2 Channel Management Advance Parameters C/I Estimate Value 22 Channel Management Advance Parameters Target CIR Offset of IBCA New Call 7 Channel Management Advance Parameters Corrected Factor of IBCA Priority 0 Channel Management Advance Parameters Target CIR Offset of IBCA Set-up Call 4 Channel Management Advance Parameters IBCA Set-up Call Soft Block Threshold Offset 0 Channel Management Advance Parameters IBCA ICDM Initial Level Offset 10 Channel Management Advance Parameters Cell Operator Power Group Not Shared Channel Management Advance Parameters Idle TCH Threshold on BCCH TRX 2 Channel Management Advance Parameters IBCA Handover Soft Block Threshold Offset 0 Channel Management Advance Parameters Type of Cell Load Calculation Count dynamic PDCH(Idle) Other Basic Parameter Report Speech Quality Report Other Basic Parameter Power Boost before HO Enabled or Not StartUp Public Channel Control Parameter Radio Resource Report Period 10 Public Channel Control Parameter CCCH Load Indication Period 15 Public Channel Control Parameter CCCH Load Threshold 80 Public Channel Control Parameter Overload Indication Period 15 Public Channel Control Parameter Average RACH Load Timeslot Number 5000 Public Channel Control Parameter SDCCH Congestion Flow Control Allowed Yes Public Channel Control Parameter PWRC Yes Public Channel Control Parameter MS_TXPWR_MAX_CCH 5 Public Channel Control Parameter Support Half Rate Yes Extended Parameter Data Service Allowed 110111000 Extended Parameter SMCBC DRX Yes Extended Parameter Cell Directed Retry Forbidden Threshold 90 Extended Parameter Interference Band Threshold 0 115 Extended Parameter Interference Band Threshold 1 108 Extended Parameter Interference Band Threshold 2 104 Extended Parameter Interference Band Threshold 3 98 Extended Parameter Interference Band Threshold 4 90 Extended Parameter Interference Band Threshold 5 85 Extended Parameter Interference Calculation Period 20 Extended Parameter Max RC Power Reduction 5 Extended Parameter Frame Start Time 65535 Extended Parameter Power Output Error Threshold 2 Extended Parameter Power Output Reduction Threshold 2 Extended Parameter VSWR TRX Unadjusted Threshold 2 Extended Parameter VSWR TRX Error Threshold 2 Extended Parameter Frame Offset 0 Extended Parameter UL Frequency Adjust Switch No Extended Parameter DL Frequency Adjust Switch No Extended Parameter UL Frequency Adjust Value 36671 Extended Parameter Reserved TCH Number for PA Turning On 2 Extended Parameter UL Level Threshold for SDCCH Call Drop 6 Extended Parameter DL Level Threshold for SDCCH Call Drop 6 Extended Parameter UL Quality Threshold for SDCCH Call Drop 55 Extended Parameter DL Quality Threshold for SDCCH Call Drop 55 Extended Parameter Power Derating Enabled No Extended Parameter Cell Weak Coverage DL RxLev Threshold 20 Extended Parameter Cell Weak Coverage TA Threshold 1 Extended Parameter Cell Over Coverage DL RxLev Threshold 30 Extended Parameter Cell Over Coverage TA Threshold 1 Extended Parameter Cell Coverage Type Outdoor Cell Extended Parameter UL Level Threshold for TCH Call Drop 1 Extended Parameter DL Level Threshold for TCH Call Drop 6 Extended Parameter UL Quality Threshold for TCH Call Drop 60 Extended Parameter DL Quality Threshold for TCH Call Drop 60 Extended Parameter UL FER Threshold for TCH Call Drop 40 Extended Parameter DL FER Threshold for TCH Call Drop 40 Extended Parameter FER Threshold 1 2 Extended Parameter FER Threshold 2 4 Extended Parameter FER Threshold 3 8 Extended Parameter FER Threshold 4 16 Extended Parameter FER Threshold 5 32 Extended Parameter FER Threshold 6 64 Extended Parameter FER Threshold 7 128 Extended Parameter Information Exchange Switch at Iur-g No Extended Parameter Low VQI Threshold 100 Reserved Parameter Item Index 1~30 Reserved Parameter Value 65535 Soft Parameter Aiding Delay Protect Time 15 Soft Parameter Directly Magnifier BTS Flag No Soft Parameter Drop Optimize Err Ind[T200 timeout] 1 Soft Parameter Drop Optimize Err Ind[unsolicited DM response] 1 Soft Parameter Drop Optimize Err Ind[sequence error] 1 Soft Parameter Drop Optimize Conn Fail[radio link fail] 1 Soft Parameter Drop Optimize Conn Fail[HO access fail] 1 Soft Parameter Drop Optimize Conn Fail[OM intervention] 1 Soft Parameter Drop Optimize Conn Fail[resource not available] 1 Soft Parameter Drop Optimize Conn Fail[other] 1 Soft Parameter Drop Optimize Release Indication 1 Soft Parameter Drop Optimize ABIS Link Failure 1 Soft Parameter Drop Optimize Equipment Failure 1 Soft Parameter Drop Optimize Forced Handover Failure 1 Soft Parameter Drop Optimize No MR for Long Time 1 Soft Parameter Drop Optimize Resource Check 1 Soft Parameter Drop Optimize Into-BSC Handover Timeout 1 Soft Parameter Drop Optimize Out-BSC Handover Timeout 1 Soft Parameter Drop Optimize Intra-BSC Handover Timeout 1 Soft Parameter Drop Optimize Intra-Cell Handover Timeout 1 Soft Parameter Frequency Scan Result Type MaximumMeanValue Soft Parameter Assignment Procedure in Intra-Cell HO Allowed No Soft Parameter Force MS to Send Ho Access SWITCH Yes Soft Parameter Sublink Resources Preemption Switch No Soft Parameter Low-level Sublink Resource Preempt Switch No Soft Parameter Cell Out-of-Service Alarm Switch Yes Soft Parameter Interfere Band Stat Algorithm Type INTBANI Soft Parameter Cell Paging Package Switch Forced turn-on Soft Parameter Interval for Sending Cell Paging Package 2 Soft Parameter Number of Cell Pagings in One Package 5 Soft Parameter MS Capability Statistic Switch Off Soft Parameter SD Quick HO Off Soft Parameter Allow Forced EFR in Cell No Soft Parameter Average Paging Message Number In Period 180 Soft Parameter MAX Paging Message Number In Period 220 Soft Parameter EICC Allowed Yes Soft Parameter Query Classmark after In-BSC HO Enabled No Soft Parameter Send Classmark ENQ Result to MSC Enabled No Soft Parameter TCH Time Handover Switch Off Soft Parameter TCH Time Handover Period 60 Soft Parameter Flex TSC Switch Off Soft Parameter Dummy Bit Randomization Switch Off Soft Parameter Stop Send SI 5/5bis/5ter after Encrypt Off Soft Parameter Activate L2 Re-establishment No Soft Parameter Bad Quality Disconnection Threshold 55 Soft Parameter Timer for Bad Quality DISC Statistic 3 Soft Parameter Report Downlink VQI Allowed Enable Soft Parameter Location Group Power Switch All Location TRXes be Turned On Soft Parameter FER Report Enable Yes Soft Parameter PDCH Power Saving Enable No Soft Parameter Switch for BTS Supporting SAIC PC Adjust Off Soft Parameter TSC Plan Enable No Soft Parameter ARFCN Coding Scheme CA+MA Soft Parameter High Band Indicator of Cell 1900 1 Soft Parameter High Band Indicator of Cell 900 1 Soft Parameter High Band Indicator of Cell 850 1 Soft Parameter Cell Paging Overload Threshold 4 Soft Parameter Um Interface Crosstalk Optimization Allowed Not Allowed Soft Parameter QTRU Signal Merge Avoid Switch Close Soft Parameter BTS Paging Lifetime 255 Soft Parameter Mute Detect Class1 Switch DISABLE Soft Parameter Period of Mute Detect Class1 5 Soft Parameter Exceptional Frame Threshold of Mute Detect Class1 25 Soft Parameter Mute Detect Class2 Switch DISABLE Soft Parameter Period of Mute Detect Class2 TRAU Frame 2 Soft Parameter Period of Mute Detect Class2 4 Soft Parameter Access Prohibited Upon One-Way Audio 0 Soft Parameter Forced Call Release Upon Failed Handover in One-Way Audio No Soft Parameter Call Drop Statistic Switch after Hang up No Soft Parameter Monitoring Alarm Switch for Channel Failure Off Soft Parameter High Band Indicator of Cell 810 1 Soft Parameter Unknown Paging Response Support No Soft Parameter DL DTX Strategy MSC Strategy Timer Parameter T3101 3000 Timer Parameter IMM ASS A IF Creation Timer 5000 Timer Parameter T3103A 18000 Timer Parameter T3103C 10000 Timer Parameter T7 10000 Timer Parameter T3107 5000 Timer Parameter T3121 30000 Timer Parameter T8 25000 Timer Parameter T3109 12000 Timer Parameter T3111 1000 Timer Parameter TREESTABLISH 15000 Timer Parameter T3122 10 Timer Parameter Wait for REL Indication AMR FR 20000 Timer Parameter T3109 for AMR HR 15000 Timer Parameter T11 8 Timer Parameter Into-BSC HO REQ Queue Timer 8 Timer Parameter Timer of Reserved TCH for EMC 15 Timer Parameter Timer for UL Data Forward 180 Timer Parameter T25 5000 Lcs Parameter Latitude and Longitude Input Mode Degree Lcs Parameter NS Latitude North latitude Lcs Parameter Latitude Int Part 0 Lcs Parameter Latitude Decimal Part 0 Lcs Parameter WE Longitude East Longitude Lcs Parameter Longitude Int Part 0 Lcs Parameter Longitude Decimal Part 0 Lcs Parameter Antenna Azimuth Angle 360 Lcs Parameter Included Angle 360 Lcs Parameter Antenna Altitude Int Part 40 Lcs Parameter Antenna Altitude Decimal Part 0 Simple Broadcast Parameter Chan ID 50 Simple Broadcast Parameter Coding Scheme ENGLISH Simple Broadcast Parameter Broadcast Content SAVE 40% Simple Broadcast Parameter Broadcast Interval 6 GSM-R parameter NCH Occupy Block Number 0 GSM-R parameter NCH Start Block 0 GSM-R parameter FACCH Send Notification Msg Indication No GSM-R parameter FACCH Send Paging Msg Indication No GSM-R parameter Send FACCH Notification Priority No Priority GSM-R parameter Send FACCH Paging Priority No Priority GSM-R parameter Download Test Resend Number 5 GSM-R parameter Download Test Resend Interval 0 GSM-R parameter DRX Type Yes GSM-R parameter FACCH Msg Resend Interval 8 GSM-R parameter Channel Release Resend Number 3 GSM-R parameter Channel Release Resend Interval 10 GSM-R parameter Talker Info Interval 0 GSM-R parameter T3115 10 GSM-R parameter Ny2 10 GSM-R parameter VGCS IM Preemption Enable Yes GSM-R parameter VGCS Channel Assign in Channel Enable Yes GSM-R parameter UIC 64 GSM-R parameter eMLPP Priority Priority 4 GSM-R parameter Reserved Number of Channels for VGCS 0 GSM-R parameter Maximum Number of Channels for VGCS 255 GSM-R parameter Channel Allocation Strategy for VGCS No Priority Basic PS Attributes of 2G Cell Network Operation Mode Network Operation Mode II Basic PS Attributes of 2G Cell T3168 500ms Basic PS Attributes of 2G Cell T3192 500ms Basic PS Attributes of 2G Cell Max Duration of DRX 4 Basic PS Attributes of 2G Cell Access Burst Type 8BIT Basic PS Attributes of 2G Cell Control Acknowledge Type 4Burst Basic PS Attributes of 2G Cell BS_CV_MAX 10 Basic PS Attributes of 2G Cell PAN_DEC 1 Basic PS Attributes of 2G Cell PAN_INC 2 Basic PS Attributes of 2G Cell PAN_MAX 20 Basic PS Attributes of 2G Cell Network Control Mode NC1 Basic PS Attributes of 2G Cell Support SPLIT_PG_CYCLE on CCCH NO Basic PS Attributes of 2G Cell Packet Access Priority Packet access of level 1-4 Basic PS Attributes of 2G Cell Routing Area Color Code 1 Basic PS Attributes of 2G Cell Support 11BIT EGPRS Access YES Basic PS Attributes of 2G Cell BSS Paging Co-ordination NO Basic PS Attributes of 2G Cell Not Send Dummy Message with Extended Uplink TBF SEND Basic PS Attributes of 2G Cell Protocol Version Supported by SGSN Release 99 onwards Neighboring Cell Reselection Parameters in Systerm information of 2G Cell GPRS Temporary Offset 10db Neighboring Cell Reselection Parameters in Systerm information of 2G Cell GPRS Penalty Time 10sec Neighboring Cell Reselection Parameters in Systerm information of 2G Cell GPRS Reselection Offset -2db PRACH Parameter in System information of 2G Cell Access Control Class 0 PRACH Parameter in System information of 2G Cell Max Retransmissions for Radio Priority 1 7_Times PRACH Parameter in System information of 2G Cell Max Retransmissions for Radio Priority 2 7_Times PRACH Parameter in System information of 2G Cell Max Retransmissions for Radio Priority 3 7_Times PRACH Parameter in System information of 2G Cell Max Retransmissions for Radio Priority 4 7_Times PRACH Parameter in System information of 2G Cell S Value 20 PRACH Parameter in System information of 2G Cell TX_INT 20 PRACH Parameter in System information of 2G Cell Persistence Level 1 12_level PRACH Parameter in System information of 2G Cell Persistence Level 2 13_level PRACH Parameter in System information of 2G Cell Persistence Level 3 14_level PRACH Parameter in System information of 2G Cell Persistence Level 4 16_level Service Parameters in PS Domain System Information of 2G Cell Cell Access Bar Switch Permit Cell Access Service Parameters in PS Domain System Information of 2G Cell Exclusive Access NoExclusive Service Parameters in PS Domain System Information of 2G Cell Minimum Receiving level for Access 2 Service Parameters in PS Domain System Information of 2G Cell Maximum TX Power for Access PCH 2 Service Parameters in PS Domain System Information of 2G Cell Cell HCS Prior Class 2 Service Parameters in PS Domain System Information of 2G Cell Threshold of HCS Signal Strength -110dB Service Parameters in PS Domain System Information of 2G Cell Multi-Band Report Report six Reselection Parametes in System Information of 2G Cell GPRS Cell Reselect Hysteresis 2dB Reselection Parametes in System Information of 2G Cell GPRS Cell Reselect Hysteresis Applied to C31 Criterion Use c31 standard Reselection Parametes in System Information of 2G Cell Exceptional Rule for GPRS Reselect Offset 0 Reselection Parametes in System Information of 2G Cell Allow MS to Access to Another Cell Yes Reselection Parametes in System Information of 2G Cell Cell Reselection Forbidden Time 10sec Reselection Parametes in System Information of 2G Cell Accessorial Hysteresis of Cell Selection 2dB PSI1 Information of 2G Cell PSI1 Repetition Period 6 PSI1 Information of 2G Cell Allow MR Command or not No PSI1 Information of 2G Cell Support PSI Status Message No Extension Measurement Parameters Extension Measurement Command EM0 Extension Measurement Parameters NCC Permitted 1 Extension Measurement Parameters Interference Frequency 1 Extension Measurement Parameters Extension MR Type TYPE1 Extension Measurement Parameters Extension MR Period 60sec GPRS Channel Management Parameters of 2G Cell Maximum Rate Threshold of PDCHs in a Cell 100 GPRS Channel Management Parameters of 2G Cell Uplink Multiplex Threshold of Dynamic Channel Conversion 20 GPRS Channel Management Parameters of 2G Cell Downlink Multiplex Threshold of Dynamic Channel Conversion 20 GPRS Channel Management Parameters of 2G Cell PDCH Uplink Multiplex Threshold 70 GPRS Channel Management Parameters of 2G Cell PDCH Downlink Multiplex Threshold 80 GPRS Channel Management Parameters of 2G Cell Dynamic Channel Conversion Parameter of Concentric Cell Only convert at UL GPRS Channel Management Parameters of 2G Cell Timer of Releasing Idle Dynamic Channel 10 GPRS Channel Management Parameters of 2G Cell Level of Preempting Dynamic Channel No preempt of CCHs GPRS Channel Management Parameters of 2G Cell Reservation Threshold of Dynamic Channel Conversion 2 GPRS Channel Management Parameters of 2G Cell Timer of Releasing Abis Timeslot 10 GPRS Channel Management Parameters of 2G Cell THP1-ARP1 Priority Weight 10 GPRS Channel Management Parameters of 2G Cell THP1-ARP2 Priority Weight 6 GPRS Channel Management Parameters of 2G Cell THP1-ARP3 Priority Weight 4 GPRS Channel Management Parameters of 2G Cell THP2-ARP1 Priority Weight 8 GPRS Channel Management Parameters of 2G Cell THP2-ARP2 Priority Weight 4 GPRS Channel Management Parameters of 2G Cell THP2-ARP3 Priority Weight 3 GPRS Channel Management Parameters of 2G Cell THP3-ARP1 Priority Weight 6 GPRS Channel Management Parameters of 2G Cell THP3-ARP2 Priority Weight 3 GPRS Channel Management Parameters of 2G Cell THP3-ARP3 Priority Weight 2 GPRS Channel Management Parameters of 2G Cell Background-ARP1 Priority Weight 4 GPRS Channel Management Parameters of 2G Cell Background-ARP2 Priority Weight 2 GPRS Channel Management Parameters of 2G Cell Background-ARP3 Priority Weight 1 GPRS Channel Management Parameters of 2G Cell BestEffort-ARP1 Priority Weight 8 GPRS Channel Management Parameters of 2G Cell BestEffort-ARP2 Priority Weight 4 GPRS Channel Management Parameters of 2G Cell BestEffort-ARP3 Priority Weight 2 GPRS Channel Management Parameters of 2G Cell PDCH Reforming NO GPRS Channel Management Parameters of 2G Cell MSRD PDCH Multiplex Threshold 40 GPRS Channel Management Parameters of 2G Cell MSRD MCS Threshold MCS5 GPRS Channel Management Parameters of 2G Cell RTTI PDCH Multiplex Threshold 30 GPRS Channel Management Parameters of 2G Cell Number of Dynamic Channel Pre-Converted 0 GPRS Channel Management Parameters of 2G Cell Number of Reserved Dynamic Channel 0 GPRS Channel Management Parameters of 2G Cell Allocate One PDCH for Signaling Data OFF GPRS Channel Management Parameters of 2G Cell Upper Threshold for CS Idle Channel Rate 100 GPRS Channel Management Parameters of 2G Cell Lower Threshold for CS Idle Channel Rate 10 GPRS Channel Management Parameters of 2G Cell Inter_Cell PS Resource Preempt Allowed No GPRS Channel Management Parameters of 2G Cell Inter_Cell PS Resource Preempted Allowed No GPRS Channel Management Parameters of 2G Cell PS Service Busy Threshold 80 GPRS Coding Scheme of 2G Cell Uplink Fixed CS Type UNFIXED GPRS Coding Scheme of 2G Cell Uplink Default CS Type CS1 GPRS Coding Scheme of 2G Cell Uplink TBF Threshold from CS1 to CS2 5 GPRS Coding Scheme of 2G Cell Uplink TBF Threshold from CS2 to CS3 2 GPRS Coding Scheme of 2G Cell Uplink TBF Threshold from CS3 to CS4 2 GPRS Coding Scheme of 2G Cell Uplink TBF Threshold from CS2 to CS1 10 GPRS Coding Scheme of 2G Cell Uplink TBF Threshold from CS3 to CS2 5 GPRS Coding Scheme of 2G Cell Uplink TBF Threshold from CS4 to CS3 5 GPRS Coding Scheme of 2G Cell Downlink Fixed CS Type UNFIXED GPRS Coding Scheme of 2G Cell Downlink Default CS Type CS2 GPRS Coding Scheme of 2G Cell Downlink TBF Threshold from CS1 to CS2 5 GPRS Coding Scheme of 2G Cell Downlink TBF Threshold from CS2 to CS3 2 GPRS Coding Scheme of 2G Cell Downlink TBF Threshold from CS3 to CS4 2 GPRS Coding Scheme of 2G Cell Downlink TBF Threshold from CS2 to CS1 10 GPRS Coding Scheme of 2G Cell Downlink TBF Threshold from CS3 to CS2 5 GPRS Coding Scheme of 2G Cell Downlink TBF Threshold from CS4 to CS3 5 EGPRS Parameter of 2G Cell Link Quality Control Mode IR EGPRS Parameter of 2G Cell Bep Period 5 EGPRS Parameter of 2G Cell Uplink Fixed MCS Type UNFIXED EGPRS Parameter of 2G Cell Uplink Default MCS Type MCS2 EGPRS Parameter of 2G Cell Downlink Fixed MCS Type UNFIXED EGPRS Parameter of 2G Cell Downlink Default MCS Type MCS6 EGPRS Parameter of 2G Cell Uplink EGPRS2-A Fixed MCS Type UNFIXED EGPRS Parameter of 2G Cell Uplink EGPRS2-A Default MCS Type MCS6 EGPRS Parameter of 2G Cell Downlink EGPRS2-A Fixed MCS Type UNFIXED EGPRS Parameter of 2G Cell Downlink EGPRS2-A Default MCS Type DAS6 EGPRS Parameter of 2G Cell Support EGPRS Uplink MCS Dynamic Adjust According to uplink quality measurements reported by BTS Customized Network Optimzation Parameters of 2G Cell Release Delay of Non-extended Uplink TBF 120 Customized Network Optimzation Parameters of 2G Cell Inactive Period of Extended Uplink TBF 2000 Customized Network Optimzation Parameters of 2G Cell Release Delay of Downlink TBF 2400 Customized Network Optimzation Parameters of 2G Cell Downlink TBF Establishment Delay 140 Customized Network Optimzation Parameters of 2G Cell PS DTX OFF Standard Network Optimization of 2G Cells Maximum Value of N3101 20 Standard Network Optimization of 2G Cells Maximum Value of N3103 3 Standard Network Optimization of 2G Cells Maximum Value of N3105 10 Power Control Parameters in System Information of 2G Cell ALPHA 06 Power Control Parameters in System Information of 2G Cell GAMMA 12 Power Control Parameters in System Information of 2G Cell T_AVG_W 10 Power Control Parameters in System Information of 2G Cell T_AVG_T 10 Power Control Parameters in System Information of 2G Cell Pb -2dB Power Control Parameters in System Information of 2G Cell PC_MEAS_CHAN PDCH Power Control Parameters in System Information of 2G Cell N_AVG_I 2 Power Control Parameters in System Information of 2G Cell Support PS Downlink Power Control No Other GPRS Parameter of 2G Cell Support GBR QoS Not Support Other GPRS Parameter of 2G Cell Move Immediate Assignment Down to BTS Not Support Other GPRS Parameter of 2G Cell Move Packet Assignment Down to BTS Not Support Other GPRS Parameter of 2G Cell Min GBR for POC Service 6 Other GPRS Parameter of 2G Cell Max GBR for POC Service 16 Other GPRS Parameter of 2G Cell Transmission Delay of POC Service 650 Other GPRS Parameter of 2G Cell Support QoS Optimize Not Support Other GPRS Parameter of 2G Cell Extended Cell Throughput Enhancement Close Other GPRS Parameter of 2G Cell GSM-to-TD Cell Reselection Allowed Support Other GPRS Parameter of 2G Cell POC Support Support Other GPRS Parameter of 2G Cell Preempt Switch of Streaming Resource OFF Other GPRS Parameter of 2G Cell User Plane DL Flow Ctrl Switch OFF Other GPRS Parameter of 2G Cell PS Initial Access Service Type Neutral Priority Other GPRS Parameter of 2G Cell Downlink GPRS TBF Window Expansion Optimization 0 Other GPRS Parameter of 2G Cell Support PS Service in Priority Not Support Other GPRS Parameter of 2G Cell MAC Scheduling Type Round Robin Schedule Other GPRS Parameter of 2G Cell Downlink Minimum Guaranteed Rate 10 Other GPRS Parameter of 2G Cell Rate Filter Time Window 50 Other GPRS Parameter of 2G Cell Time to Wait Coding in BTS 10 NC2 Parameters Cell Reselection Level Threshold 15 NC2 Parameters Cell Reselection Hysteresis 6 NC2 Parameters Cell Penalty Level 30 NC2 Parameters Cell Penalty Duration 10 NC2 Parameters Allowed Measure Report Missed Number 4 NC2 Parameters Filter Window Size 6 NC2 Parameters MS Rx Quality Statistic Threshold 200 NC2 Parameters Cell Rx Quality Worsen Ratio Threshold 30 NC2 Parameters Load Reselection Start Threshold 85 NC2 Parameters Load Reselection Receive Threshold 60 NC2 Parameters Cell Urgent Reselection Allowed Permit NC2 Parameters Cell Load Reselection Allowed Permit NC2 Parameters Cell Normal Reselection Allowed Permit NC2 Parameters Normal Cell Reselection Watch Period 10 NC2 Parameters Normal Cell Reselection Worsen Level Threshold 1 NC2 Parameters Cell Reselect Interval 2 NC2 Parameters EDGE GMSK Quality Threshold 7 NC2 Parameters EDGE 8PSK Quality Threshold 16 NC2 Parameters GPRS Quality Threshold 5 NC2 Parameters Load Reselect Level Threshold 40 Network Control Measurement Parameters Non-DRX Period 024sec Network Control Measurement Parameters Cell Reselection MR Period in Packet Idle Mode 1536sec Network Control Measurement Parameters Cell Reselection MR Period in Packet Transfer Mode 096sec BSC 2G Neighbor Cell Neighboring Cell Type Handover Neighboring Cell BSC 2G Neighbor Cell Current HO CTRL Algorithm in Source Cell Handover algorithm I BSC 2G Neighbor Cell Inter-cell HO Hysteresis 68 BSC 2G Neighbor Cell Min Access Level Offset 0 BSC 2G Neighbor Cell PBGT HO Threshold 68 BSC 2G Neighbor Cell BQ HO Margin 68 BSC 2G Neighbor Cell Chain Neighbor Cell No BSC 2G Neighbor Cell Adjacent Cell Inter-layer HO Hysteresis 68 BSC 2G Neighbor Cell Directed Retry Handover Level Range 71 BSC 2G Neighbor Cell Chain Neighbour Cell Type QUICK_HO_NCELL_TYPE_A BSC 2G Neighbor Cell Edge HO AdjCell Watch Time 2 BSC 2G Neighbor Cell Edge HO AdjCell Valid Time 1 BSC 2G Neighbor Cell Layer HO Watch Time 6 BSC 2G Neighbor Cell Layer HO Valid Time 4 BSC 2G Neighbor Cell PBGT Watch Time 8 BSC 2G Neighbor Cell PBGT Valid Time 6 BSC 2G Neighbor Cell Better Cell HO Watch Time 6 BSC 2G Neighbor Cell Better Cell HO Valid Time 4 BSC 2G Neighbor Cell Quick Handover Static Time 4 BSC 2G Neighbor Cell Quick Handover Last Time 3 BSC 2G Neighbor Cell HCS HO Watch Time 3 BSC 2G Neighbor Cell HCS HO Valid Time 2 BSC 2G Neighbor Cell BQ HO Watch Time 1 BSC 2G Neighbor Cell BQ HO Valid Time 1 BSC 2G Neighbor Cell TA HO Watch Time 1 BSC 2G Neighbor Cell TA HO Valid Time 1 BSC 2G Neighbor Cell UL BQ HO Static Time 1 BSC 2G Neighbor Cell UL BQ HO Last Time 1 BSC 2G Neighbor Cell Load HO PBGT Threshold 0 BSC 2G Neighbor Cell Neighboring Cell Priority 255 Utran FDD Handover Data Better 3G Cell HO Allowed No Utran FDD Handover Data Inter-rat HO Preference Preference 2G cell by thresh Utran FDD Handover Data HO Preference Threshold for 2G Cell 25 Utran FDD Handover Data RSCP Threshold for Better 3G Cell HO 50 Utran FDD Handover Data Ec/No Threshold for Better 3G Cell HO 35 Utran Tdd Handover Parameter Inter-rat HO Preference Preference 2G cell by thresh Utran Tdd Handover Parameter HO Preference Threshold for 2G Cell 25 Utran Tdd Handover Parameter RSCP Threshold for Better 3G Cell HO 50 Utran Tdd Handover Parameter Better 3G Cell HO Allowed No Inter-RAT Handover Parameters Allow Inter-RAT Load HO in Connect State No Inter-RAT Handover Parameters Allow Inter-RAT Load HO in Access State OFF Inter-RAT Handover Parameters 2G Cell UL Basic Congest Thred 90 Inter-RAT Handover Parameters 2G Cell UL Overload Congest Thred 100 Inter-RAT Handover Parameters 2G Cell DL Basic Congest Thred 90 Inter-RAT Handover Parameters 2G Cell DL Overload Congest Thred 100 Inter-RAT Handover Parameters Inter-RAT CS Service HO Load Threshold 80 Inter-RAT Handover Parameters 2G Load Adjustment Coefficient 10 Inter-RAT Handover Parameters Inter-RAT Load HO RSCP Threshold 30 Inter-RAT Handover Parameters Inter-RAT Load HO EcNo Threshold 25 Inter-RAT Handover Parameters Inter-RAT Hierarchical Load HO Period 10 Inter-RAT Handover Parameters Inter-RAT Hierarchy Load HO Step [RSCP] 10 Inter-RAT Handover Parameters Inter-RAT Hierarchy Load HO Step [EcNo] 5 Inter-RAT Handover Parameters Inter-RAT Load HO Bandwidth [RSCP] 60 Inter-RAT Handover Parameters Inter-RAT Load HO Bandwidth [EcNo] 20 Inter-RAT Handover Parameters Inter-RAT Load HO RSCP at Start Point 91 Inter-RAT Handover Parameters Inter-RAT Load HO EcNo at Start Point 49 Cell Priority and EUTRAN System Information Parameter GERAN Priority 7 Cell Priority and EUTRAN System Information Parameter UTRAN Priority 1 Cell Priority and EUTRAN System Information Parameter EUTRAN Priority 0 Cell Priority and EUTRAN System Information Parameter Inter-RAT Search THD Based on Priority 15 Cell Priority and EUTRAN System Information Parameter Low GSM Threshold Based on Priority 0 Cell Priority and EUTRAN System Information Parameter UTRAN Cell Resel High THD Based on PRI 20 Cell Priority and EUTRAN System Information Parameter UTRAN Cell Resel Low THD Based on PRI 20 Cell Priority and EUTRAN System Information Parameter Min RX Level of UTRAN Cell Based on PRI 9 Cell Priority and EUTRAN System Information Parameter EUTRAN Cell Resel High THD Based on PRI 20 Cell Priority and EUTRAN System Information Parameter EUTRAN Cell Resel Low THD Based on PRI 20 Cell Priority and EUTRAN System Information Parameter Min RX Level of EUTRAN Cell Based on PRI 9 Cell Priority and EUTRAN System Information Parameter Cell Resel Level Hyst Based on PRI 0 Cell Priority and EUTRAN System Information Parameter Cell Resel Time Hyst Based on PRI 0 Cell Priority and EUTRAN System Information Parameter Number EUTRAN Cells in Best Cell List 2 Cell Priority and EUTRAN System Information Parameter EUTRAN Cell Reporting Threshold 0 Sheet2 Sheet3